TIAO GBoard/GIMX Board Hardware Layout

From TIAO's Wiki
Revision as of 15:46, 27 April 2016 by Admin (talk | contribs) (TIAO GBoard/GIMX Adapter Connector Layouts)
Jump to: navigation, search

10 PCS, 10cm x 10cm, 2 layers prototype for $38.80 shipped!

TIAO GBoard / GIMX Adapter

For system connection diagram as GIMX adapter, please refer to TIAO GIMX System Connection Diagram.

The TIAO GBoard / GIMX adapter is a combined all in one board for serial and AVR development. It also provides jumper connections for easy and quick GIMX connectoion (to be used as a GIMX Game Input MultipleXer or Game Input MatriX adapter. For more information on GIMX, please check it out here.

The TIAO GBoard/GIMX Adapter features:

  • All in one board contains USB to COM adapter and ATMEVA32U4 for AVR development.
  • Bootloader is installed on the ATMEGA32U4, so you don't need a programmer to load the firmware.
  • Quick connection jumpers to convert the GBoard to a GIMX adapter
  • RX/TX LED, enable LEDs or use the pins for IO ports

TIAO GBoard/GIMX Adapter Hardware Dimensions

The board dimension of TSS is 59.56 x 40.26mm. It also has 4 mounting holes, the radius of the mounting hole is 2.5mm:

Gimx-size.png


TIAO GBoard/GIMX Adapter Connector Layouts

The following picture shows the connector layout of the TIAO GBoard/GIMX Adapter.

Gimx-pins.png
  1. USB to COM RX LED
  2. USB to COM TX LED
  3. GIMX TXD Enable
  4. GIMX RXD Enable
  5. ATMEGA32U4 Power Select
  6. ATMEGA32U4 USB Connector
  7. FT231X USB Connector
  8. ATMEGA32U4 IO Pin Header 1
  9. ATMEGA32U4 IO Pin Header 2
  10. FT231X IO Pin Header

J1

Gimx-j1.png
  • Jumper on: Enable RX Led for USB to COM/Serial.
  • Jumper off: Enable CBUS1 output for FT231X.


J2

Gimx-j2.png
  • Jumper on: Enable TX Led for USB to COM/Serial.
  • Jumper off: Enable CBUS2 output for FT231X.

J3

Gimx-j3.png
  • Jumper on: Enable board to be a DIY GIMX adapter (J4 has to be on as well)
  • Jumper off: Enable board to be a AVR and USB to Serial development board. (J4 has to be off as well)
Gimx-j4.png
  • Jumper on: Enable board to be a DIY GIMX adapter (J3 has to be on as well)
  • Jumper off: Enable board to be a AVR and USB to Serial development board. (J3 has to be off as well)


RF Header

Tss-RF.png
Pin # Description
1 A3 - Data
2 VIN - 5V
3 GND

Radio Frequency (RF) transmitter header. Works with standard 434MHz or 315MHz RF transmitter.

ISP header

None

Pin # Description
1 MISO
2 VIN - 5V
3 SCK
4 MOSI
5 RESET
6 GND

Extension board header

None

Pin # Description
1 Vcc - 3.3V
2 QH*
3 A4/ADC4
4 Clock/TOSC1
5 GND
6 Latch/AIN1
7 GND
8 OE/T1

Connect any extension boards to this header.

MicroSD socket

None Optional MicroSD socket for logging.

AVR Power selector

None Select power source for AVR Microcontroller. Default is 3.3v. 3.3v Power: jumper over pin 1 and 2. 5V power: jumper over pin 2 and 3.


Relay header

None

Pin # Description
1 NC - Normally closed pin
2 CO - Change over pin
3 NO - Normally open pin

The relay is rated as 250V/3A/AC or 30V/3A/DC, however for safety concerns, please DO NOT connect anything higher than 28V/2A.

Soft button 1

Tss-B1.png

The function of B1/B2/B3 depends on the firmware version. For version 2.1.4, these are the functions:

Press then release Press and hold
Display current IP address Stop all stations immediately.

Soft button 2

Tss-B2.png

The function of B1/B2/B3 depends on the firmware version. For version 2.1.4, these are the functions:

Press then release Press and hold
Display MAC address Restart controller


Soft button 3

Tss-B3.png

The function of B1/B2/B3 depends on the firmware version. For version 2.1.4, these are the functions:

Press then release Press and hold
Toggle between the main controller (MC) and each expansion board (E1, E2, etc). Manually start an existing program or a test program.


LCD display header

Tss-LCD.png

Insert the LCD module directly on the LCD header. Make sure pins are aligned, otherwise the LCD/controller will be damaged.


Ethernet receptacle

Tss-Net.png

Plug Ethernet cable here for network access. If wired network is not available, there are many other options, such as using a wireless router in client mode (for example: 150Mbps Wireless N Nano Router (Micro USB Power) TL-WR702N or 150Mbps Wireless N Mini Pocket Router (direct power) TL-WR700N) or powerline network adapter kit (Linxe LSP06 200Mbps etherent powerline network adapter Kit (2)).


Fuse holder

None

The on board fuse hold. The fuse is rated at 2A.

Power switch

Tss-Pwr.png

The main power switch. Slide up to turn on the controller, slide down to turn off the controller.

Power status LED

Tss-PwrLED.png

Power status LEDs.

Pin Description
PWR ON: VIN (5V) is working
V33 ON: Vcc (3.3V) is working

24V AC and rain sensor header

None

This header allows you to connect the power (24V, 2A AC) to the TSS. This is the only power source needed for the controller. For power, connect one of the 24V AC 2A transformer's terminal to pin 8 (24V AC In) and the other terminal to pin 7 (GND) For rain sensor, connect one of the rain sensor's terminal to pin 5 (Rain sensor terminal) and the other terminal to pin 6. The rain sensor is optional.

Pin Description
1, 2, 3, 4 Common wire, connect to sprinkler valve's common terminals.
5 Rain sensor terminal
6, 7 GND
8 24V AC In

Station 1-16 header

None

TSS can control 16 stations (including master station if you have one) without expansion board. This header has 16 connectors, so you can connect up to 16 valves.

  • Example 1: My irrigation system has 10 stations, I do not have a master station.
    • Connect RED wires of the valves to 'Common wire' connectors (see #24V AC and rain sensor header), then connect BLACK wires of the valves to connector 1 to 10 respectively.
  • Example 2: My irrigation system has 15 stations, I have a master station.
    • Connect RED wires of the valves to 'Common wire' connectors (see #24V AC and rain sensor header), then connect BLACK wire of the the master valve to connector 16, and other BLACK wires of regular valves to connector 1 to 15 respectively.


10 PCS, 10cm x 10cm, 2 layers prototype for $38.80 shipped!