Difference between revisions of "TIAO Smart Sprinkler Pi Hardware Layout"

From TIAO's Wiki
Jump to: navigation, search

10 PCS, 10cm x 10cm, 2 layers prototype for $38.80 shipped!
(Analog pins)
(Analog pins)
Line 122: Line 122:
 
| GND
 
| GND
 
|}
 
|}
 +
 +
 +
==== I2C Pins 1 ====
 +
[[Image:TSSPi-c3.png||None]]
 +
 +
PI2C heard connects to Raspberry Pi's I2C pins:
 +
{|
 +
! align="left"|Pin #
 +
! Description
 +
|-
 +
| 1, 2
 +
| Vcc
 +
|-
 +
| 3, 4
 +
| SDA
 +
|-
 +
| 5, 6
 +
| SCL
 +
|-
 +
| 7, 8
 +
| GND
 +
|}
 +
 +
The relay is rated as 120V/2A, however for safety concerns, please connect anything higher than 36V/2A.

Revision as of 22:52, 28 August 2014

TIAO Smart Sprinkler Pi

The TIAO Smart Sprinkler Pi (TSSPi) is a piece of hardware controls your irrigation systems. It replaces your traditional sprinkler controller. TSSPi has many benefits over the traditional sprinkler controller:

  • Web interface - program the watering schedule using your PC or mobile phone
  • Supports complicate watering schedules
  • Unlimited watering schedules
  • Allow seasonal adjustments
  • Weather API access - automatically adjust watering amount/time by checking online weather forecast (rain/wind etc)
  • Control your sprinkler stations from anywhere in the world
  • Software supports unlimited stations
  • Total of 16 stations (or 1 master station + 15 stations), can expend to unlimited stations using our extension board
  • Software supports unlimited stations
  • Supports rain sensor
  • Open source software - which means you can add your own function to the controller!
  • System ON/OFF hardware switch
  • Status LEDs (power, Pi power, system on, system running)
  • Low cost! It's cheaper than the traditional sprinkler controller!

TSSPi Hardware Dimensions

The board dimension of TSSPi is 122.5 x 87mm, or 48.2 x 34.2 inch. It also has 4 mounting holes, the radius of the mounting hole is 2mm:

TSSPi-dimension.png


TSSPi Connector Layouts

The following picture shows the connector layout of the TSSPi. You can plug the Raspberry pi directly on top of TSSPi without using any wires. It also has two mounting holes so you can mount the Raspberry Pi on the TSSPi.

TSSPi-layout.png


  1. Relay port
  2. [[#|]]
  3. [[#|]]
  4. [[#|]]
  5. [[#|]]
  6. [[#|]]
  7. [[#|]]
  8. [[#|]]
  9. [[#|]]
  10. [[#|]]
  11. [[#|]]
  12. [[#|]]
  13. [[#|]]


Relay Port

None

Pin # Description
1 NC - Normally closed pin
2 CO - Change over pin
3 NO - Normally open pin

The relay is rated as 120V/2A, however for safety concerns, please connect anything higher than 36V/2A.


Analog pins

None

The TSSPi has on board PCF8591 8 bit AD/DA converter. The JP1 header on the board maps to the pins on PCF8591.

Pin # PCF8591 Pin Description
1 AIN0 (1) Analog input 0
2 NC 5V
3 AIN1 (2) Analog input 1
4 A0 (5), A1 (6), A2 (7), VSS (8), AGND (13), EXT (12) GND
5 AIN2 (3) Analog input 2
6 VDD (16) Vcc
7 AIN3 (4) Analog input 3
8 VDD (16) Vcc
9 AOUT (15) Analog output
10 A0 (5), A1 (6), A2 (7), VSS (8), AGND (13), EXT (12) GND


I2C Pins 1

None

PI2C heard connects to Raspberry Pi's I2C pins:

Pin # Description
1, 2 Vcc
3, 4 SDA
5, 6 SCL
7, 8 GND

The relay is rated as 120V/2A, however for safety concerns, please connect anything higher than 36V/2A.



10 PCS, 10cm x 10cm, 2 layers prototype for $38.80 shipped!