Difference between revisions of "TIAO Xilinx XC2C64A CoolRunner-II CPLD Dev Board (Reset Glitch) Tutorial"

10 PCS, 10cm x 10cm, 2 layers prototype for $38.80 shipped!

Revision as of 21:08, 21 November 2011

Buy various JTAG cables for your Satellite Receiver, Cable Modem, Wireless Router, Standard Wiggler from http://www.easymg.com and http://www.diygadget.com

Overview

In this tutorial, I am going to show you how to install TIAO Xilinx XC2C64A CoolRunner-II CPLD Dev Board (Reset Glitch) on your XBOX 360.

TIAO CoolRunner II Installed on Slim: (Thanks to Roger!)

Required Hardware and Software

• TIAO Xilinx XC2C64A CoolRunner-II CPLD Dev Board (Reset Glitch)
• Soldering iron and solder
• Optional: XBOX 360 Case Opening Torx Tools

TIAO Xilinx CoolRunner-II Dev Board Overview

When we designed this board, we only had on goal in our mind: make it simple. Simple to install, simple to use. We achieved it. You don't need to solder any components, no jumper wires, it even provides a on-board 5v to 3.3v LDO (Low-drop Voltage Regulator) for JTAG programming. One board works for all.

Key features:

• Pre-populated required components for phat: 100nF Cap, 1K and 22K Resistors, three 1N4148 Diodes.
• Pre-populated required component for slim: 220pF cap. However, we also added two 3-30pF trimmer capacitors, thus the capacitance can be easily adjusted from 226pF to 280pF.
• The dev board ships with four female to female (50cm / 20 inch in length) flexible wires, cut the wires in half, solder one end to your mother board and insert the female headers to the pins on our dev board. This allows you to quickly remove the board for upgrading or testing.

Pinout of the board:

Install it on slim

Jumper Positions

There are three jumpers on the dev board. You can move jumpers on different positions for slim or phat. The default configuration is for slim.

Here is the jumper positions if you want to install it on a slim:

Use a jumper to short P2.1 and P2.2
Use a jumper to short P2.3 and P2.4
Use a jumper to short P2.5 and P2.7 (optional)
No jumpers on other headers

Here is the photo (this is the default configuration):

Solder the wires

First, you need to disassemble your slim. For slim, you need to install 7 wires. The package contains 4 female to female wires, so you cut them all in half and you will have 8 wires. The female header side will be put on top of the dev board's headers, and the cut end will be soldered onto the mother board.

Now, locate the following soldering points on your slim mother board:

on the back of the mother board: CPU_RST, POST_OUT1

slim back

On the front side of the mother board: V-3P3STBY, I2C_SCL, I2C_SDA, STBY_CLK, and GND

Slim front

Now solder 7 wires onto these points.

Double check your soldering make sure no short circuits

Use isolation type to fix the dev board on your mother board, then insert other end (female header) of these 7 wires to the dev board by the following configuration:

Now you have successfully installed the dev board on your slim.

Adjust Capacitance for Slim

Install it on Phat

Jumper Positions

There are three jumpers on the dev board. You can move jumpers on different positions for slim or phat. The default configuration is for slim.

Here is the jumper positions if you want to install it on a phat:

Put a jumper on P2.5 and P2.6
Put a jumper on P2.7 and P2.8
Put a jumper on P2.8 and P2.10
No jumpers on other headers

Here is the photo of jumper positions on a phat:

Solder the wires

Disassemble your phat. For phat, you need to install 6 wires. The package contains 4 female to female wires, so you cut three in half and you will have 6 wires. The female header side will be put on top of the dev board's headers, and the cut end will be soldered onto the mother board.

Now, locate the following soldering points on your phat mother board:

on the back of the mother board: CPU_PLL_BYPASS, POST_OUT1

phat back

On the front side of the mother board: V-3P3STBY, CPU_RST_V1P1_N, STBY_CLK, and GND

phat front

Now solder 6 wires onto these points.

Double check your soldering make sure not short circuit

Use isolation type to fix the dev board on your mother board, then insert other end (female header) of these 7 wires to the dev board by the following configuration:

Now you have successfully installed the dev board on your phat.

Program TIAO CoolRunner-II Dev Board Using JTAG

It is fairly easy to program TIAO CoolRunner-II Dev Board. All you need to do is to connect the JTAG pins (TDI, TDO, TMS and TDO) to the corresponding pins on your JTAG programmer.

We have the following tutorials on how to program CPLD using our Universal JTAG Adapter:

• Program Xilinx XC2C64A Or Similar Xilinx CPLD Using TIAO Universal JTAG Cable

As to power the CPLD, you can either use external +3.3V power source (available on our Universal JTAG adapter) to power your our CoolRunner-II, (the board has built in 1.8v LDO), or power it by USB (use the on board USB connector. The board has built in 3.3v and 1.8v LDO). However when choosing different power source, you need to move jumpers on different headers.

Debug Pin

Buy various JTAG cables for your Satellite Receiver, Cable Modem, Wireless Router, Standard Wiggler from http://www.easymg.com and http://www.diygadget.com

10 PCS, 10cm x 10cm, 2 layers prototype for $38.80 shipped!