Difference between revisions of "Xbox 360 Lite On DVD Key Dumping - TIAO's Serial Key Extractor"

From TIAO's Wiki
Jump to: navigation, search

10 PCS, 10cm x 10cm, 2 layers prototype for $38.80 shipped!
Line 17: Line 17:
  
 
You can also search on [[http://www.360drives.com/list XBOX 360 DVD Drive Database]] for more information.
 
You can also search on [[http://www.360drives.com/list XBOX 360 DVD Drive Database]] for more information.
 
  
 
== How it works ==
 
== How it works ==
Line 36: Line 35:
  
 
[[http://www.llamma.com/xbox360/repair/Xbox-360-Disassembly.htm How to disassemble XBOX 360 case]]
 
[[http://www.llamma.com/xbox360/repair/Xbox-360-Disassembly.htm How to disassemble XBOX 360 case]]
 
  
 
== Step 2: Remove Lite-On DVD drive back cover ==
 
== Step 2: Remove Lite-On DVD drive back cover ==
Line 43: Line 41:
  
 
[[Image:remove_liteon_dvd_seal.jpg|left|thumb|Cut the seal]]
 
[[Image:remove_liteon_dvd_seal.jpg|left|thumb|Cut the seal]]
 +
  
 
Locate the 4 screws on the DVD drive, remove these screws:
 
Locate the 4 screws on the DVD drive, remove these screws:

Revision as of 22:07, 21 December 2008

Why you need to extract the key?

The newer XBOX 360 comes with lite-on DVD drive. It is impossible do dump the firmware from these lite-on DVD drives. However, a new method was developed so you can at least extract the DVD key / identification from these lite-ons. You can then use the key/identification to spoof iXtreme and flash the spoofed iXtreme to a SAMSUNG/LG/BENQ or even the original Lite-on (after Dec 24/2008).

Lite-On DG16D2S

This drive started to appear in machines manufactured after 20th April 2008 (2008-04-20).

Here is how to figure out whether you have a lite-on or not:

  1. Remove XBOX 360 front Faceplate
  2. See which colour the wires are in the hole under the DVD Tray
  3. Yellow wires: you have lite-on DVD drive
  4. White wires: you have BENQ drive

Lite on DVD has yellow wire

You can also search on [XBOX 360 DVD Drive Database] for more information.

How it works

Basically, you will need to perform the following steps:

  1. Disassemble XBOX 360 (Remove Lite-on DVD drive from XBOX 360)
  2. Remove Lite-on DVD back cover
  3. Extract DVD key and identification strings
  4. Prepare spoofed iXtreme firmware
  5. Flash the spoofed firmware to a BENQ/SAMSUNG/LG or original Lite-on

OK. Let's get started!

Step 1: Disassemble XBOX 360

There are tons instructions on how to disassemble XBOX 360, you can follow these instructions:

[How to disassemble XBOX 360 case]

Step 2: Remove Lite-On DVD drive back cover

Put the DVD drive on a table, locate the seal on the side of the back cover, use a utility knife to cut the seal:

Cut the seal


Locate the 4 screws on the DVD drive, remove these screws:

Remove screws

Remove the back cover and get familiar with the area we will be working on:

Remove the back cover

A closer look of the area we will be working on. We will be working on the bottom pad of R707 as shown in the picture below:

Bottom pad of R707 on Lite-On DVD drive


10 PCS, 10cm x 10cm, 2 layers prototype for $38.80 shipped!