Difference between revisions of "TIAO USB Multi Protocol Adapter User's Manual"
From TIAO's Wiki
10 PCS, 10cm x 10cm, 2 layers prototype for $38.80 shipped!
(→DB9 Male RS232) |
(→DB9 Male RS232) |
||
Line 65: | Line 65: | ||
! Description | ! Description | ||
|- | |- | ||
− | |1 | + | | 1 |
− | | | + | | DCD |
− | | | + | | Data Carrier Detect |
− | | | + | | <<-- |
− | | | + | | Modem connected to another |
+ | |- | ||
+ | | 2 | ||
+ | | RxD | ||
+ | | Receive Data | ||
+ | | <<-- | ||
+ | | Receives bytes into PC | ||
+ | |- | ||
+ | | 3 | ||
+ | | TxD | ||
+ | | Transmit Data | ||
+ | | -->> | ||
+ | | Transmits bytes out of PC | ||
+ | |- | ||
+ | | 4 | ||
+ | | DTR | ||
+ | | Data Terminal Ready | ||
+ | | -->> | ||
+ | | I'm ready to communicate | ||
+ | |- | ||
+ | | 5 | ||
+ | | SG | ||
+ | | Signal Ground | ||
+ | | | ||
+ | | Ground/GND | ||
+ | |- | ||
+ | | 6 | ||
+ | | DSR | ||
+ | | Data Set Ready | ||
+ | | <<-- | ||
+ | | I'm ready to communicate | ||
+ | |- | ||
+ | | 7 | ||
+ | | RTS | ||
+ | | Request To Send | ||
+ | | -->> | ||
+ | | RTS/CTS flow control | ||
+ | |- | ||
+ | | 8 | ||
+ | | CTS | ||
+ | | Clear To Send | ||
+ | | <<-- | ||
+ | | RTS/CTS flow control | ||
+ | |- | ||
+ | | 9 | ||
+ | | RI | ||
+ | | Ring Indicator | ||
+ | | <<-- | ||
+ | | Telephone Line Ringing | ||
|} | |} |
Revision as of 16:10, 9 August 2011
Overview
The TIAO USB Multi Protocol Adapter (TUMPA) is a multi-functional USB communication adapter for hobbyists or engineers. The adapter is based on FDTI's flagship communication chip FT2232H, a USB 2.0 Hi-Speed (480Mb/s) to UART/FIFO IC. It has two multi-protocol synchronous serial engines (MPSSEs) which allow for communication using JTAG, I2C and SPI on two channels simultaneously.
Technical Specifications
- USB 2.0 Hi-Speed (480Mb/s)
- JTAG / IEEE 1149.1 compatible.
- JTAG Baudrate up to 30Mbits/sec (programmable)
- On board voltage translation via 74LVC14T245 (can be enabled / disabled via software or jumper)
- JTAG signals are 5V to 1.8V tolerant
- ARM Muli-ICE 20-pin header compatible.
- Separate SPI/I2C/Serial interfaces
- Configurable output of RS232 (MAX3243) or TTL level for serial communication
- Configurable auto power down for MAX3243
- Target board can be powered by TUMPA (3.3V) or self powered (via jumper)
- 4 on-board LEDs / PWR, Targt PWR, TX and RX
- 1 2x10 20 PIN JTAG header
- 1 2x5 10 PIN RS232 level 2.54mm IDC header
- 1 2x6 10 PIN TTL level 2.54mm IDC header
- 2 2x3 6 PIN SPI 2.54mm IDC header
- 1 x DB9 connector (male, RS232 level)
- Target board power jumper
- Buffer chip enable jumper
- RS232 chip auto power down jumper
- RS232 or TTL output jumber
- USB Hot-Plug / JTAG Hot-Plug.
- USB over-current protection via on-board resetable fuse.
- Strong ESD protection on USB signals.
- Based on the FTDI FT2232H USB device.
- Designed for FTDI MPSSE easy-to-use.
- Free drivers for Linux.
- Free drivers for Windows XP, Windows Vista and Windows 7
- Support both 32 bit and 64 bit operating systems
- Board dimension: 65.41mm X 58.55mm (2.58" X 2.31")
Board Layout
- DB9 male RS232 connector (Channel B)
- 2x3 standard 6 PIN 2.54mm IDC SPI connector (Channel A)
- 2x10 standard 20 PIN 2.54mm IDC JTAG connector (Channel A)
- Auto power down jumper header for MAX3243 (force on or auto power down). Default force on (jumper is on pin 1and 2)
- Buffer enable jumper header for 74LVC16T245. Default is always enabled. (jumper on pin 2 and 3)
- Target voltage select jumper. Default is to power target board by TUMPA (3.3V only) (jumper on pin 1 and 2)
- 3x8 PIN RS232 or TTL level serial communication jumpmer. Default is RS232 output (jumpers short rowtop and middle rows) (Channel B)
- 2x6 PIN TTL level 2.54mm IDC serial header (channel B)
- 2x3 PIN 2.54mm IDC SPI header (channel B)
- Target board power LED. Indicates target board has power.
- Status LEDs. From left to right: Power (indicates TUMPA is powered on), RX and TX.
Connector Pinout
DB9 Male RS232
Pin # | Acronym | Full name | Direction | Description |
---|---|---|---|---|
1 | DCD | Data Carrier Detect | <<-- | Modem connected to another |
2 | RxD | Receive Data | <<-- | Receives bytes into PC |
3 | TxD | Transmit Data | -->> | Transmits bytes out of PC |
4 | DTR | Data Terminal Ready | -->> | I'm ready to communicate |
5 | SG | Signal Ground | Ground/GND | |
6 | DSR | Data Set Ready | <<-- | I'm ready to communicate |
7 | RTS | Request To Send | -->> | RTS/CTS flow control |
8 | CTS | Clear To Send | <<-- | RTS/CTS flow control |
9 | RI | Ring Indicator | <<-- | Telephone Line Ringing |
10 PCS, 10cm x 10cm, 2 layers prototype for $38.80 shipped!