Difference between revisions of "TIAO USB Multi Protocol Adapter User's Manual"
From TIAO's Wiki
10 PCS, 10cm x 10cm, 2 layers prototype for $38.80 shipped!
(→20 PIN JTAG Connector) |
(→Board Layout) |
||
Line 42: | Line 42: | ||
# [[#DB9_Male_RS232|DB9 male RS232 connector (Channel B)]] | # [[#DB9_Male_RS232|DB9 male RS232 connector (Channel B)]] | ||
# [[#SPI_Connector_1|2x3 standard 6 PIN 2.54mm IDC SPI connector (Channel A)]] | # [[#SPI_Connector_1|2x3 standard 6 PIN 2.54mm IDC SPI connector (Channel A)]] | ||
− | # 2x10 standard 20 PIN 2.54mm IDC JTAG connector (Channel A) | + | # [[#20_PIN_JTAG_Connector|2x10 standard 20 PIN 2.54mm IDC JTAG connector (Channel A)]] |
# Auto power down jumper header for MAX3243 (force on or auto power down). Default force on (jumper is on pin 1and 2) | # Auto power down jumper header for MAX3243 (force on or auto power down). Default force on (jumper is on pin 1and 2) | ||
# Buffer enable jumper header for 74LVC16T245. Default is always enabled. (jumper on pin 2 and 3) | # Buffer enable jumper header for 74LVC16T245. Default is always enabled. (jumper on pin 2 and 3) |
Revision as of 16:32, 9 August 2011
Contents
Overview
The TIAO USB Multi Protocol Adapter (TUMPA) is a multi-functional USB communication adapter for hobbyists or engineers. The adapter is based on FDTI's flagship communication chip FT2232H, a USB 2.0 Hi-Speed (480Mb/s) to UART/FIFO IC. It has two multi-protocol synchronous serial engines (MPSSEs) which allow for communication using JTAG, I2C and SPI on two channels simultaneously.
Technical Specifications
- USB 2.0 Hi-Speed (480Mb/s)
- JTAG / IEEE 1149.1 compatible.
- JTAG Baudrate up to 30Mbits/sec (programmable)
- On board voltage translation via 74LVC14T245 (can be enabled / disabled via software or jumper)
- JTAG signals are 5V to 1.8V tolerant
- ARM Muli-ICE 20-pin header compatible.
- Separate SPI/I2C/Serial interfaces
- Configurable output of RS232 (MAX3243) or TTL level for serial communication
- Configurable auto power down for MAX3243
- Target board can be powered by TUMPA (3.3V) or self powered (via jumper)
- 4 on-board LEDs / PWR, Targt PWR, TX and RX
- 1 2x10 20 PIN JTAG header
- 1 2x5 10 PIN RS232 level 2.54mm IDC header
- 1 2x6 10 PIN TTL level 2.54mm IDC header
- 2 2x3 6 PIN SPI 2.54mm IDC header
- 1 x DB9 connector (male, RS232 level)
- Target board power jumper
- Buffer chip enable jumper
- RS232 chip auto power down jumper
- RS232 or TTL output jumber
- USB Hot-Plug / JTAG Hot-Plug.
- USB over-current protection via on-board resetable fuse.
- Strong ESD protection on USB signals.
- Based on the FTDI FT2232H USB device.
- Designed for FTDI MPSSE easy-to-use.
- Free drivers for Linux.
- Free drivers for Windows XP, Windows Vista and Windows 7
- Support both 32 bit and 64 bit operating systems
- Board dimension: 65.41mm X 58.55mm (2.58" X 2.31")
Board Layout
- DB9 male RS232 connector (Channel B)
- 2x3 standard 6 PIN 2.54mm IDC SPI connector (Channel A)
- 2x10 standard 20 PIN 2.54mm IDC JTAG connector (Channel A)
- Auto power down jumper header for MAX3243 (force on or auto power down). Default force on (jumper is on pin 1and 2)
- Buffer enable jumper header for 74LVC16T245. Default is always enabled. (jumper on pin 2 and 3)
- Target voltage select jumper. Default is to power target board by TUMPA (3.3V only) (jumper on pin 1 and 2)
- 3x8 PIN RS232 or TTL level serial communication jumpmer. Default is RS232 output (jumpers short rowtop and middle rows) (Channel B)
- 2x6 PIN TTL level 2.54mm IDC serial header (channel B)
- 2x3 PIN 2.54mm IDC SPI header (channel B)
- Target board power LED. Indicates target board has power.
- Status LEDs. From left to right: Power (indicates TUMPA is powered on), RX and TX.
Connector Pinout
DB9 Male RS232
This connector is enabled only if RS232/TTL jumpers are on RS232-OUT
Pin # | Acronym | Full name | Direction | Description |
---|---|---|---|---|
1 | DCD | Data Carrier Detect | <<-- | Modem connected to another |
2 | RxD | Receive Data | <<-- | Receives bytes into PC |
3 | TxD | Transmit Data | -->> | Transmits bytes out of PC |
4 | DTR | Data Terminal Ready | -->> | I'm ready to communicate |
5 | SG | Signal Ground | Ground/GND | |
6 | DSR | Data Set Ready | <<-- | I'm ready to communicate |
7 | RTS | Request To Send | -->> | RTS/CTS flow control |
8 | CTS | Clear To Send | <<-- | RTS/CTS flow control |
9 | RI | Ring Indicator | <<-- | Telephone Line Ringing |
SPI Connector 1
Pin # | Description |
---|---|
1 | MISO |
2 | Vcc (connected to on board 3.3V) |
3 | SCK |
4 | MOSI |
5 | CS |
6 | GND |
20 PIN JTAG Connector
Pin # | Description |
---|---|
1 | VTAR |
3 | nTRST |
5 | TDI |
7 | TMS |
9 | TCK |
11 | RTCK |
13 | TDO |
15 | RST |
17 | DBGRQ |
19 | DBGACK |
2 | Not Connected |
4, 6, 8, 10, 12, 14, 16, 18, 20 | GND |
10 PCS, 10cm x 10cm, 2 layers prototype for $38.80 shipped!