Difference between revisions of "How to install Liteon Switch for Your XBOX 360 Liteon DVD"

From TIAO's Wiki
Jump to: navigation, search

10 PCS, 10cm x 10cm, 2 layers prototype for $38.80 shipped!
(How to install it)
(How to install it)
Line 45: Line 45:
 
[[Image:Ls-ready.jpg|none|thumb|Ready]]
 
[[Image:Ls-ready.jpg|none|thumb|Ready]]
  
Put the TIAO liteon switch on top of the PCB, to make sure it matches the spots you just have the paint removed.  You will need to solder on the 4 circled area.
+
Put the TIAO liteon switch on top of the PCB, to make sure it matches the spots you just have the paint removed.  You will need to solder on the 5 circled area.
  
 
[[Image:Ls-ready2.jpg|none|thumb|Put the switch on top of the PCB]]
 
[[Image:Ls-ready2.jpg|none|thumb|Put the switch on top of the PCB]]
Line 51: Line 51:
 
Once you have the paint removed and cuts are done, double check the cut by using a multimeter, then add a little solder paste on the spot you will be soldering the switch (the spots you just have the paint removed).
 
Once you have the paint removed and cuts are done, double check the cut by using a multimeter, then add a little solder paste on the spot you will be soldering the switch (the spots you just have the paint removed).
  
The put t
+
Now, it's time to solder the Liteon Switch to the PCB:
 +
 
 +
[[
  
 
<span class="plainlinks">
 
<span class="plainlinks">

Revision as of 14:50, 27 July 2010








Buy Game Console Adapters from http://www.easymg.com or http://www.diygadget.com

What is this for?

We released Solderless Liteon Kit for Liteon DVD drive almost half years ago, however we still got lots of requests to offering a solder kit, here you go, we have it! And it is also easy to install!

Solderless Liteon Kit: ck3-83850-93450-600.jpg

Solder Lite on Kit: ck3-lt_switch_600.jpg

Key features

  • 6 solder points (compare to other switch's 7 solder points)
  • 3 cuts on the PCB
  • Solder on traces (Other liteon switch will require you to solder on vias, which could damage your via)
  • On board 22/20/18 Ohm selection switch, and also be reached after the PCB is installed in the DVD casing.
  • On board Normal/RW switch, and also be reached after the PCB is installed in the DVD casing.
  • One time installation, one installed, you can you just leave it there, no need to remove.
  • Works for all Liteon DVDs: 74850, 83850 V1, 83850 V2, 93450. (For 74650, you don't really need to install it, you can extract the key even easier: [Xbox 360 Lite On DVD Key Dumping - TIAO's USB Key Extractor]

How to install it

Open 360 case, take out the DVD drive, and remove the PCB from the DVD case. There are plenty of tutorials on how to do this, just google it.

Now you have the DVD PCB out on your desk, you first need to make 3 cuts as below. You don't need to clean the paint on top of the bottom cut. However you need to remove the paint between the top 2 cuts, as you will need to solder on this point later on. Use a utility knife to cut the traces, make sure the cut is good. it is always a good idea to check if the cuts are good using a multimeter.

You need to make 3 cuts on the PCB

After the cut is done, mark the area of the traces you will need to solder the Liteon Switch to:

Remove the paint from the trace

You can use a sand paper to sand the paint off, or use an utility knife to carefully scratch the paint off:

Ready

Put the TIAO liteon switch on top of the PCB, to make sure it matches the spots you just have the paint removed. You will need to solder on the 5 circled area.

Put the switch on top of the PCB

Once you have the paint removed and cuts are done, double check the cut by using a multimeter, then add a little solder paste on the spot you will be soldering the switch (the spots you just have the paint removed).

Now, it's time to solder the Liteon Switch to the PCB:

[[


Buy Game Console Adapters from http://www.easymg.com or http://www.diygadget.com



10 PCS, 10cm x 10cm, 2 layers prototype for $38.80 shipped!