TIAO GBoard/GIMX Board Hardware Layout

From TIAO's Wiki
Revision as of 11:16, 9 June 2016 by Admin (talk | contribs) (J5)
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to: navigation, search

10 PCS, 10cm x 10cm, 2 layers prototype for $38.80 shipped!

TIAO GBoard / GIMX Adapter

For system connection diagram as GIMX adapter, please refer to TIAO GIMX System Connection Diagram. For loading the firmware, please refer to How to Install GIMX Firmware on TIAO GBoard/GIMX Adapter

The TIAO GBoard / GIMX adapter is a combined all in one board for serial and AVR development. It also provides jumper connections for easy and quick GIMX connectoion (to be used as a GIMX Game Input MultipleXer or Game Input MatriX adapter. For more information on GIMX, please check it out here.

The TIAO GBoard/GIMX Adapter features:

  • All in one board contains USB to COM adapter and ATMEVA32U4 for AVR development.
  • Bootloader is installed on the ATMEGA32U4, so you don't need a programmer to load the firmware.
  • Quick connection jumpers to convert the GBoard to a GIMX adapter
  • RX/TX LED, enable LEDs or use the pins for IO ports

TIAO GBoard/GIMX Adapter Hardware Dimensions

The board dimension of TSS is 59.56 x 40.26mm. It also has 4 mounting holes, the radius of the mounting hole is 2.5mm:

Gimx-size.png


TIAO GBoard/GIMX Adapter Connector Layouts

The following picture shows the connector layout of the TIAO GBoard/GIMX Adapter.

Gimx-pins.png
  1. USB to COM RX LED
  2. USB to COM TX LED
  3. GIMX TXD Enable
  4. GIMX RXD Enable
  5. ATMEGA32U4 Power Select
  6. ATMEGA32U4 USB Connector
  7. FT231X USB Connector
  8. ATMEGA32U4 IO Pin Header 1
  9. ATMEGA32U4 IO Pin Header 2
  10. FT231X IO Pin Header
  11. ATMEGA32U4 Bootloader Pin

J1

Gimx-j1.png
  • Jumper on: Enable RX Led for USB to COM/Serial.
  • Jumper off: Enable CBUS1 output for FT231X.


J2

Gimx-j2.png
  • Jumper on: Enable TX Led for USB to COM/Serial.
  • Jumper off: Enable CBUS2 output for FT231X.

J3

Gimx-j3.png
  • Jumper on: Enable board to be a DIY GIMX adapter (J4 has to be on as well)
  • Jumper off: Enable board to be a AVR and USB to Serial development board. (J4 has to be off as well)

J4

Gimx-j4.png
  • Jumper on: Enable board to be a DIY GIMX adapter (J3 has to be on as well)
  • Jumper off: Enable board to be a AVR and USB to Serial development board. (J3 has to be off as well)


J5

Gimx-j5.png
  • Jumper on 1-2: Enable 5.0V IO on ATMEGA32U4.
  • Jumper on 2-3: Enable 3.3V IO on ATMEGA32U4.

ATMEGA32U4 USB Connector

Gimx-6.png
  • The USB connector for ATMEGA32U4.

FT232X USB Connector

Gimx-7.png
  • The USB connector for FT231X.

ATMEGA32U4 IO Pin Header 1

Gimx-8.png
Pin # ATMEGA32U4 Pin
1 GND
2 +5V
3 RST (Low)
4 PE6
5 PB0
6 PB1
7 PB2
8 PB3
9 PB7
10 PD0
11 PD1
12 PD2
13 PD5
14 PD3
15 PC6
16 PC7

ATMEGA32U4 IO Pin Header 2

Gimx-9.png
Pin # ATMEGA32U4 Pin
1 GND
2 Vcc (5.0 or 3.3 depending on J5)
3 Vcc (5.0 or 3.3 depending on J5)
4 AREF
5 PF0
6 PF1
7 PF4
8 PF5
9 PF6
10 PF7
11 PB6
12 PB5
13 PB4
14 PD7
15 PD6
16 PD4


FT231X IO Pin Header

None

Pin # FT231X Pin
1 RTS
2 DTR
3 RI
4 RXD
5 DSR
6 DCD
7 TXLED/CBUS2
8 CTS
9 RXLED/CBUS1
10 CBUS0
11 CBUS3
12 TXD
13 V5
14 V33
15 GND
16 GND

ATMEGA32U4 Bootloader Pin

  • ATMEGA32U4 Bootloader Pin, press and hold to enter bootloader mode.


10 PCS, 10cm x 10cm, 2 layers prototype for $38.80 shipped!