TIAO USB Multi Protocol Adapter Lite User's Manual

From TIAO's Wiki
Revision as of 13:26, 6 October 2012 by Admin (talk | contribs)
Jump to: navigation, search

10 PCS, 10cm x 10cm, 2 layers prototype for $38.80 shipped!








Buy various JTAG cables for your Satellite Receiver, Cable Modem, Wireless Router, Standard Wiggler from http://www.easymg.com and http://www.diygadget.com


Overview

The TIAO USB Multi Protocol Adapter Lite (TUMPA Lite) is a multi-functional USB communication adapter for hobbyists or engineers. The adapter is based on FDTI's flagship communication chip FT232H, a USB 2.0 Hi-Speed (480Mb/s) to UART/FIFO IC. It has one multi-protocol synchronous serial engines (MPSSEs) which allow for communication using JTAG, I2C and SPI on two channels simultaneously.


Technical Specifications

  • Single channel USB to serial / parallel ports with a variety of configurations.
  • Entire USB protocol handled on the chip. No USB specific firmware programming required.
  • USB 2.0 Hi-Speed (480Mbits/Second) and Full Speed (12Mbits/Second) compatible.
  • Multi-Protocol Synchronous Serial Engine (MPSSE) to simplify synchronous serial protocol (USB to JTAG, I2C, SPI or bit-bang) design.
  • UART transfer data rate up to 12Mbaud. (RS232 Data Rate limited by external level shifter).
  • USB to asynchronous 245 FIFO mode for transfer data rate up to 8 MByte/Sec.
  • USB to synchronous 245 parallel FIFO mode for transfers up to 40 Mbytes/Sec
  • Supports a half duplex FT1248 interface with a configurable width, bi-directional data bus (1, 2, 4 or 8 bits wide).
  • CPU-style FIFO interface mode simplifies CPU interface design.
  • Fast serial interface option.
  • FTDI's royalty-free Virtual Com Port (VCP) and Direct (D2XX) drivers eliminate the requirement for USB driver development in most cases.
  • Adjustable receive buffer timeout.
  • Option for transmit and receive LED drive signals.
  • Bit-bang Mode interface option with RD# and WR strobes
  • Highly integrated design includes 5V to 3.3/+1.8V LDO regulator for VCORE, integrated POR function
  • Asynchronous serial UART interface option with full hardware handshaking and modem interface signals.
  • Fully assisted hardware or X-On / X-Off software handshaking.
  • UART Interface supports 7/8 bit data, 1/2 stop bits, and Odd/Even/Mark/Space/No Parity.
  • Auto-transmit enable control for RS485 serial applications using TXDEN pin.
  • Operation configuration mode and USB Description strings configurable in external EEPROM over the USB interface.
  • Configurable I/O drives strength (4, 8, 12 or 16mA) and slew rate.
  • Low operating and USB suspend current.
  • Supports self powered, bus powered and high-power bus powered USB configurations.
  • UHCI/OHCI/EHCI host controller compatible.#
  • USB Bulk data transfer mode (512 byte packets in Hi-Speed mode).
  • +1.8V (chip core) and +3.3V I/O interfacing (+5V Tolerant).
  • Extended -40°C to 85°C industrial operating temperature range.
  • Compact 48-pin Lead Free LQFP or QFN package
  • Configurable ACBUS I/O pins.
  • 4 on-board LEDs / PWR, +3.3V Out, TX and RX
  • 1 2x10 20 PIN JTAG header
  • 1 2x3 6 PIN SPI 2.54mm IDC header
  • 1 SPI MISO pullup config IDC header
  • 1 Configurable TX/RX LED IDC header
  • On board 3.3V LDO
  • USB over-current protection via on-board resetable fuse.
  • Strong ESD protection on USB signals.
  • Based on the FTDI FT232H USB device.
  • Designed for FTDI MPSSE easy-to-use.
  • Free drivers for Linux.
  • Free drivers for Windows XP, Windows Vista and Windows 7
  • Support both 32 bit and 64 bit operating systems
  • Board dimension: 48.64mm X 70.61mm (1.91" X 2.78")

Board Dimensions

Board Layout

Tumpa.board.layout.png
  1. DB9 male RS232 connector (Channel B)
  2. 2x3 standard 6 PIN 2.54mm IDC SPI connector (Channel A)
  3. RS232 Level 2.54mm IDC Header
  4. 2x10 standard 20 PIN 2.54mm IDC JTAG connector (Channel A)
  5. Auto power down jumper header for MAX3243 (force on or auto power down). Default force on (jumper is on pin 1and 2)
  6. Buffer enable jumper header for 74LVC16T245. Default is always enabled. (jumper on pin 2 and 3)
  7. Buffer chip 74LVC16T245 Vcc(B) power select jumper. Default is to power Vcc(B) by TUMPA (3.3V only) (jumper on pin 1 and 2)
  8. 3x8 PIN RS232 or TTL level serial communication jumpmer. Default is RS232 output (jumpers short top row and middle rows) (Channel B)
  9. 2x6 PIN TTL level 2.54mm IDC serial header (channel B)
  10. 2x3 PIN 2.54mm IDC SPI header (channel B)
  11. Status LEDs. From left to right: Power (indicates TUMPA is powered on), RX and TX
  12. Target board power LED. Indicates target board has power

Connector Pinout & LEDs

DB9 Male RS232

This connector is enabled only if RS232/TTL jumpers are on RS232-OUT, see Serial RS232/TTL level Selection Jumper

Tumpa.rs232.connector.1.pngTumpa.rs232.connector.2.png

Pin # Acronym Full name Direction Description
1 DCD Data Carrier Detect <<-- Modem connected to another
2 RxD Receive Data <<-- Receives bytes into PC
3 TxD Transmit Data -->> Transmits bytes out of PC
4 DTR Data Terminal Ready -->> I'm ready to communicate
5 SG Signal Ground Ground/GND
6 DSR Data Set Ready <<-- I'm ready to communicate
7 RTS Request To Send -->> RTS/CTS flow control
8 CTS Clear To Send <<-- RTS/CTS flow control
9 RI Ring Indicator <<-- Telephone Line Ringing

SPI Connector 1

Tumpa.spi1.connector.1.png
Pin # Description
1 MISO
2 Vcc (connected to on board 3.3V)
3 SCK
4 MOSI
5 CS
6 GND

RS232 Level 2.54mm IDC Header

This connector is enabled only if RS232/TTL jumpers are on RS232-OUT, see Serial RS232/TTL level Selection Jumper

Tumpa.rs232.connector.png

For your convenience, we added this header. This header is inter connected to the DB9 connector. The pinout is different then the pinout of DB 9 connector, however the extra pin (PIN 10) is connected to on board 3.3V power. GND pin (PIN 9) and +3.3V PIN (PIN 10) are always enabled regardless the jumpers position of Serial RS232/TTL level Selection Jumper.

This is the pinout of the RS232 level 2.54mm IDC header:


Pin # Description
1 RI
2 DCD
3 DSR
4 CTS
5 RX
6 TX
7 RTS
8 DTR
9 GND
10 +3.3V

20 PIN JTAG Connector

Tumpa.jtag.connector.1.png
Pin # Description
1 VTAR
3 nTRST
5 TDI
7 TMS
9 TCK
11 RTCK
13 TDO
15 RST
17 DBGRQ
19 DBGACK
2 Not Connected
4, 6, 8, 10, 12, 14, 16, 18, 20 GND


MAX3243 Auto Power Down Jumper

Tumpa.auto.power.down.max3243.1.png

This jumper controls whether to always enable MAX3243 or let FT2232H automatically enables it (save power).

  • Jumper on PIN 1 and PIN 2: Always enable MAX3243
  • Jumper on PIN 2 and PIN 3: FT2232H (PWREN, PIN 60)controls when to enable or disable MAX3243.

Buffer Enable Jumper

Tumpa.buff.enable.connector.1.png

This jumper controls whether to software enable/disable buffer chip (74LVC16T254).

  • Jumper on PIN 1 and PIN 2: Enable (Low)/Disable (High) 74LVC16T245 via FT2232H's ACBUS3 (PIN 29).
  • Jumper on PIN 2 and PIN 3: Always enable 74LVC16T245

Buffer Chip Power Selection Jumper

Tumpa.vtar.sel.connector.1.png

This jumper controls how to power the buffer / voltage translator chip (74LVC16T245)

The 74LVC16T245's Vcc(A) is connected to on board +3.3V. You can either power the Vcc(B) using on board +3.3V or powered by the target board. If powered by target board, please make sure the target board's power is in the range of +1.8V - +5.5V.

  • Jumper on PIN 1 and PIN 2: Power the buffer chip 74LVC16T245's Vcc(B) via the on board +3.3V source.
  • Jumper on PIN 2 and PIN 3: Power the buffer chio 74LVC16T245's Vcc(B) by target board. (PIN 3 of this header is connected to JTAG header's PIN 1)


Serial RS232/TTL level Selection Jumper

Tumpa.rs232.ttl.connector.1.png

These jumpers allows you to have serial communication at either RS232 level or TTL level.

TTL Level Serial Connector

This connector is enabled only if RS232/TTL jumpers are on TTL-OUT, see Serial RS232/TTL level Selection Jumper

Tumpa.ttl.connector.png


Pin # Description
1 Tx
2 Rx
3 RTS
4 CTS
5 DTR
6 DSR
7 DCD
8 RI
9 +3.3V
10 +5V (USB Power)
11, 12 GND

The power pins (9, 10, 11 and 12) are always connected, regardless of the jumper positions of Serial RS232/TTL level Selection Jumper.


SPI Connector 2

Tumpa.spi2.connector.1.png
Pin # Description
1 MISO
2 Vcc (connected to on board 3.3V)
3 SCK
4 MOSI
5 CS
6 GND


PWR/RX/TX LEDs

Tumpa.led.group.1.png
  • PWR: indicates the TUMPA board is connected to USB port of the computer and on board voltage regulator outputs +3.3V.
  • RX: Indicates FT2232H is receiving bytes from target via serial communication channel B
  • TX: Indicates FT2232H is transmitting bytes to target via serial communication channel B

Target Board Power LED

Tumpa.led.vtar.1.png
  • LED is ON: Target board (PIN 1 of JTAG Header) has power supply > 3.3V.
  • LED is OFF: Target board (PIN 1 of JTAG Header) has power supply < 3.3V or no power.

The VTAR can also be detected by software. If VTAR has voltage > 3.3V, ACBUS4 (PIN 30) of FT2232H will be LOW. Otherwise it will be HIGH.

Pin Connections

FT2232H 20 PIN JTAG Header SPI Header 1 DB9 Connector RS232 Level Output Header TTL Level Output Header SPI Header 2 Memo
ADBUS0 TCK SCK
ADBUS1 TDI MOSI
ADBUS2 TDO MISO
ADBUS3 TMS CS
ADBUS4 RST
ADBUS5 nTRST
ADBUS6 DBGRQ
ADBUS7 RTCK
 
ACBUS0 DBGACK
ACBUS1 Connected to nTRST pin of JTAG Header, (input)
ACBUS2 Connected to RST pin of JTAG Header, as (input)
ACBUS3 OEN Pin (enable buffer chip), active low (output)
ACBUS4 Target present pin. Detect VTAR, active low (input)
ACBUS5
ACBUS6
ACBUS7
 
BDBUS0 TX TX TX SCK
BDBUS1 RX RX RX MOSI
BDBUS2 RTS RTS RTS MISO
BDBUS3 CTS CTS CTS CS
BDBUS4 DTR DTR DTR
BDBUS5 DSR DSR DSR
BDBUS6 DCD DCD DCD
BDBUS7 RI RI RI
 
BCBUS0
BCBUS1
BCBUS2
BCBUS3 RX LED
BCBUS4 TX LED
BCBUS5
BCBUS6
BCBUS7
 
PWREN Enable MAX3243. Active low (output)








Buy various JTAG cables for your Satellite Receiver, Cable Modem, Wireless Router, Standard Wiggler from http://www.easymg.com and http://www.diygadget.com



10 PCS, 10cm x 10cm, 2 layers prototype for $38.80 shipped!