TIAO USB Powered Buffered Wiggler/FTA JTAG Programmer Manual

From TIAO's Wiki
Revision as of 13:51, 27 September 2009 by Admin (talk | contribs) (New page: <span class="plainlinks"> [http://www.easymg.com/jtag-cables/jtag-cable-for-wireless-routers.html http://www.easymg.com/media/catalog/product/cache/2/small_image/135x135/5e06319eda06f020e4...)
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to: navigation, search

10 PCS, 10cm x 10cm, 2 layers prototype for $38.80 shipped!

DG-JTAG-S06_small.jpgDG-JTAG-S03_small_1.jpgDG-JTAG-S02_small.jpgDG-JTAG-S04_small.jpgDB-BJTAG-04_small.jpgDG-JTAG-S05_small.jpgDG-BJTAG-03_small.jpg

Buy various JTAG cables for your Satellite Receiver, Cable Modem, Wireless Router, Standard Wiggler from http://www.easymg.com and http://www.diygadget.com

TIAO USB Powered Buffered Wiggler/FTA JTAG Programmer Manual

  1. Open the package, you will find the PCB board as shown in above picture.
    The new design abandoned the batteries, instead, it can be powered by either USB port or target board. There are two USB receptacles on the board, one is USB-B and another one is Mini USB. Some target boards may provide power, thus we installed a jumper on the board, therefore you can choose whether to power from target board or from USB port.

Some target boards may require 3.3V inputs, so we have installed a LDO voltage regulator on the board, with a switch on the board, you can easily select from 5V to 3.3V output.
There are 3 LEDs on the board, so you know whether you are powering it from target board or USB, and you know whether you are outputing 5V or 3.3V.
As for the parallel port header, this board uses a male DB25 header, so it can be directly connect to your computers parallel port, so you do not need a parallel port extension cord.
We have installed two 20 pin, one 6 pin, one 14 pin and one 8 pin IDC headers on the board, the pin configurations are industry standards.
These Buffered Wiggler JTAG cables can also be used to fix dreaded GLS (Green Light Syndrome) or dead FTA units.
Specification:

    1. USB powered or powered from target board
    2. Choice of 5V and 3.3V
    3. Three LEDs indicate 5V, 3.3V and target board powered
    4. Two 20 pin headers
    5. One 14 pin header
    6. One 8 pin header
    7. One 6 pin header
    8. Free 20 pin to 20 pin flat cable with IDC sockets clampped on the flat cable
    9. Free pogo pins and alligator clip presoldered on a 6 pin flat cable
    10. Free 6 hole pogo pin adapter (holder)
    11. Free 80 pin (2 by 40) header
Wiggler.buffer.jtag.fta.jpg

DG-JTAG-S06_small.jpgDG-JTAG-S03_small_1.jpgDG-JTAG-S02_small.jpgDG-JTAG-S04_small.jpgDB-BJTAG-04_small.jpgDG-JTAG-S05_small.jpgDG-BJTAG-03_small.jpg

Buy various JTAG cables for your Satellite Receiver, Cable Modem, Wireless Router, Standard Wiggler from http://www.easymg.com and http://www.diygadget.com



10 PCS, 10cm x 10cm, 2 layers prototype for $38.80 shipped!
Retrieved from "https://www.tiaowiki.com/wiki/index.php?title=TIAO_USB_Powered_Buffered_Wiggler/FTA_JTAG_Programmer_Manual&oldid=742"